Product Information: As an upgrade of the original iTaste MVP the iTaste MVP V2.0 has substantial improvements in both appearance and function. Variable Voltage: voltage can be adjusted from 3.3 – 5.0 volts in .1 volt increments. VariableWattage: Wattage can be adjusted from 6.0 – 11.0 W in .5 watts increments. Ohmsmeter: Reads resistance of your atomizer/cartomizer/clearomizer. Battery Level Indicator: The iTaste MVP2.0 battery capacity is displayed via green, yellow and red LED lights. Green = Fully Charged When the iTaste MVP2.0 is fully charged the LED light will turn green and power off. Yellow = Half Discharged Red = In need of charging Puff Counter Short Circuit/Atomizer Protection. Over-Discharge Protection. Battery Level Indicator Large battery capacity: iTaste MVP e-cigarette built-in 2600 mAh polymer Li-Ion rechargeable battery. High compatibility 510 connector: Thread fit iClear10,iClear16 ,iClear30 etc. ON/OFF battery switch: 10 seconds cutoff. Passthrough / Vape While Charging Technology. Remembers last set voltage or wattage: Remembers last set voltage or wattage when the battery is turned off and then back on. Built-in 3 digit display: Digital display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the battery was turned off. Portable power source for electronic products.

The Primary Features of The iTaste ARACHNID: Positive connector Pin: The positive connector pin can be adjusted to varying heights. To adjust the connector pin turn the pin clockwise (+) or counterclockwise (-) Telescopic tube: To expand or contract the telescopic tube turn it Clockwise (+) and counterclockwise (-). The iTaste ARACHNID supports 18650, 18500, 18350 batteries. Working current: The iTaste ARACHNID working current = 4.2/（R+0.15），if you use a 0.45Ohm atomizer, make sure your battery minimum working current more than 7A 4.2/（0.45+0.15）。 Lock and unlock ring: To unlock and lock the firing button turn the ring counterclockwise (-) or Clockwise (+). Technical Specifications: Battery: We recommend using high quality IMR high-drain 18650, 18500, 18350 batteries. (Diameter: 18.3+/-0.2mm, Length: 34.5~66.5mm, Unprotected) The iTaste ARACHNID cannot use 2 stacked batteries. Input Voltage: 3.2~4.3V

Product Information: As an upgrade of the original iTaste MVP the iTaste MVP V2.0 has substantial improvements in both appearance and function. Variable Voltage: voltage can be adjusted from 3.3 – 5.0 volts in .1 volt increments. VariableWattage: Wattage can be adjusted from 6.0 – 11.0 W in .5 watts increments. Ohmsmeter: Reads resistance of your atomizer/cartomizer/clearomizer. Battery Level Indicator: The iTaste MVP2.0 battery capacity is displayed via green, yellow and red LED lights. Green = Fully Charged When the iTaste MVP2.0 is fully charged the LED light will turn green and power off. Yellow = Half Discharged Red = In need of charging Puff Counter Short Circuit/Atomizer Protection. Over-Discharge Protection. Battery Level Indicator Large battery capacity: iTaste MVP e-cigarette built-in 2600 mAh polymer Li-Ion rechargeable battery. High compatibility 510 connector: Thread fit iClear10,iClear16 ,iClear30 etc. ON/OFF battery switch: 10 seconds cutoff. Passthrough / Vape While Charging Technology. Remembers last set voltage or wattage: Remembers last set voltage or wattage when the battery is turned off and then back on. Built-in 3 digit display: Digital display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the battery was turned off. Portable power source for electronic products.

The iTaste VV4 is the newest in the line of bestselling Innokin Technology iTaste VV vaporizers and features a wider range of Variable Voltage, Variable Wattage, advanced safety features and also ‘Vape while charging’ Technology. The Primary Features of The iTaste VV4 Battery Level Indicator: The iTaste VV4 battery capacity is displayed via green, yellow and red LED lights. Green = Almost fully Charged. When the iTaste VV4 is fully recharged the LED light will power off. Yellow = Half Power. Red = Low Power. Charge the VV4. Variable Voltage: Voltage can be adjusted from 3.0 – 6.0 volts in .1 volt increments. Variable Wattage: Wattage can be adjusted from 6.0 – 15.0 Watts in .5 watts increments. Large battery capacity: The iTaste VV4 has a built-in 1000 mAh polymer Li-Ion rechargeable battery. ON/OFF battery switch: Press the power button three times in rapid succession to turn on the iTaste VV4. Once the iTaste VV4 is On hold down the power button to activate the atomizer and vape. When the iTaste VV4 is not in use, press the power button three times in succession to power off the iTaste VV4 Advanced Personal Vaporizer. Always power off the iTaste VV4 Advanced Personal Vaporizer when it is not being used, or when it is going to be stored in a pocket, bag or purse. SAFETY: 10 second cutoff: If the activation button is held for 10 seconds or longer the iTaste VV4 Advanced Personal Vaporizer will stop firing until the button is released and pressed again. Low Voltage Warning: The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the iTaste VV4 Advanced Personal Vaporizer will power off automatically. Short Circuit/Atomizer Protection: Short Circuit/Atomizer Protection protects the iTaste VV4 Advanced Personal Vaporizer against shorted atomizers and will stop the unit from functioning in unsafe conditions. The iTaste VV4 features automatic real-time atomizer Ohms detection. If the resistance of the atomizer is lower than 0.8 the Ohms bar will blink. If there is a short circuit the VV4 screen will display the following and the LED light will power off. Over-Discharge Protection: The iTaste VV4 Advanced Personal Vaporizer monitors the battery voltage and will automatically power off when the battery is discharged. High compatibility 510/ego connector: Threads are compatible with the following clearomizers: iClear16, iClear16B, iClear16D, iClear30, iClear30B, iClear30s, iClearX.I. Gladius and other standard 510 threading. Technical Specifications: Variable Voltage: Voltage can be adjusted from 3.0 – 6.0 volts in .1 volt increments. Variable Wattage: Wattage can be adjusted from 6.0 – 15.0 Watts in .5 watts increments. Standby current: 50uA max Maximum output current：4.0A Charging: Micro USB DC5.0V/500mA Short Circuit Protection: 0.8 Ohm